MT58C1618-15 Datasheet| PIN DESCRIPTION LOGIC SYMBOL AO-A17 = 18 Addrass Innllts (Cnmmc)n) | | I , - I U Il.J. I gOO ii iF- u LO \ .JIIII I.I i] A-1, A18-A19 = 3 Address Inputs (Flash) SA = Highest Order Address Input (SRAM) Byte mode DQO-DQ15 = 16 Data Inputs/Outputs (Common) CE#f = Chip Enable (Flash) CE#s = Chip Enable (SRAM) OE# = Output Enable (Common) WE# = Write Enable (Common) RY/BY# = Ready/BusyOutput UB#s = Upper Byte Control (SRAM) LB#s = Lower Byte Control (SRAM) ClOf = I/O Configuration (Flash) ClOf = VIH = Word mode (x16), ClOf = VIL = Byte mode (x8) ClOs = I/O Configuration (SRAM) ClOs = VIH = Word mode (x16), ClOs = VIL = Byte mode (x8) RESET# = Hardware Reset Pin, Active Low i AID44 l A t-'t-' - U^__J i Aiv ; Dv / | AO-A17 A-1, A18-A19 SA CEf DQO-DQ15 CEl#s CE2s RY/BY# OE# WE# WP#/ACC RESET# UB#s LB#s ClOf ClOs | 16 0r8 G | | vvrjmAL L = r-iaraware write r'rotecti Acceleration Pin (Flash) Vccf = Flash 3.0 volt-only single power sup- ply (see Product Selector Guide for speed options and voltage supply tolerances) Vccs = SRAM Power Supply VSS = Device Ground (Common) NC = Pin Not Connected Internally | | | |
MT58C1618-15 Price| Items | Symbols | Test Conditions | Min | Typ. | Max | Units | | | | VGE=OV VCE=600V Ti=250C | | | 1O | mA | | Zero Gate Voltage Collecter Current | ICES | VGE=OV VCE=600V Ti=1250C | | | | mA | | Gate-Emitter Leackage Current | IGES | VCE=OV VGE=t20V | | | 100 | nA | | Gate-Emitter Threshold Voltage | VGE nhl | VCE=20V lc=75mA | 3.0 | | 6.0 | V | | Collecter-Emitter Saturation Voltage | VCE lsatl | VGE=15V lc=75A | | | 2.5 | V | | Input Capacitance | Cies | VGE=OV | | 7100 | | pF | | Output Capacitance | Coes | VCE=10V | | | | | Reverse Transfer Capacitance | Cres | f=lMHz | | | | | | ton | Vcc=300V | | | O8 | | | Turn-on Time | tr | lc=75A | | | O6 | | | toff | VGE=±15V | | | 1.5 | LLS | | Turn-off Time | tf | Ro=33fl | | | 1O | | Diode Forward On-Voltage | VF | IF=75A, VGE=OV | | | 2.5 | V | | Reverse Recovery Time | trr | IF=715A, -di/dt=225A4is VGE=-IOV | | | 300 | ns | | | | | | | |
MT58C1618-15 on stock Open Drain Output. End-of-Conversion (EO ) is asserted any time the TC530/534 is in the AZ phase of conversion. This occurs when either the TC530/534 initiates a normal AZ phase or when RESET is pulled high. EOC is returned high when the TC530/534 exits AZ. Since EOC is driven low immediately following completion of a conversion cycle, it can be used as a DATA READY processor interrupt. | SYMBOL | PARAMETER | CONDITIONS | MIN | MAX | UNIT | | VS | DC supply voltage | | | 4.2 | V | | ICTRL | control current | VCTRL = 2.7 V; VSi = 4.2 V; VS2 = 4.2 V | | 1.2 | mA | | lsl | current into pin 3 | Vsl=4.2 V | | 27 | mA | | IS2 | current into pin 4 | VS2= 4.2 V | | 50 | mA | | PD | drive power | | | tbf | dBm | | Ptot | total power dissipation | Ts90 IC | | 280 | mW | | Tstg | storage temperature | | -65 | +150 | IC | | Tj | operating junction temperature | | | 150 | | | | | | | |
|
