MX27C4111PC-10，there are the best MX27C4111PC-10 suppiers all over the world here.These are the list and detailed contact method of MX27C4111PC-10 suppliers all over the world as follows.You can buy or get informations of MX27C4111PC-10 through email , message or tel.

suppliers of MX27C4111PC-10 and PDF data of MX27C4111PC-10

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

MX27C4111PC-10 Datasheet

Parameter	Symbol	Min	Max	Unit
Su pply Voltage	Vcc		5.5	V
Operating Case Temperature Range	Tc	-40	85	oC
Storage Case Temperature Range	Tstg	-40	85	oC
Lead Soldering Temperature/Time			250/10	oC/s
Operating Wavelength Range		1.1	1.6	pm
Minimum Fiber Bend Radius		1.0 (25.4)		m(mm)

MX27C4111PC-10 Price

Drain source voltage	VDS	55	V
Drain-Source on-state resistance	RDS(on)	0.012	l
Continuous drain current	D	70	A

MX27C4111PC-10 on stock

3Soldering temperature for T0-263: 2200C, reflow 4Co(er) is a fixed capacitance that gives the same stored energy as Coss while VDS iS rising from o t0 80% VDSS 5Co(tr) is a fixed capacitance that gives the same charging time as Coss while VDS iS rising from o t0 80% VDSS.

SYMBOL	SOT205AG	SOT232A	DESCRIPTION
DOBM	1	28	digital audio interface output
VSs	2	29	ground connection for the digital section
nC	3		not connected
XIN	4	30	crystal input at 256fs (8.192 MHz)
XOUT	5	31	crystal output at 256fs (8.192 MHz)
DATA	6	32	serial data input at 728 kbits/s from DQPSK demodulator
PCLK	7	1	output clock at 728 kHz to DQPSK demodulator
RESET	8	2	active LOW reset; used to set the device in a valid initial condition
SCL	9	3	clock input for I2C control bus
SDA	10	4	data port for I2C control bus, input/open drain output
PORT2	11	5	output mirroring the I2C control register bit PORT2
nC	12		not connected
ADSEL	13	6	12C_bus slave address selection input; allows selection of one of two separate slave addresses, defaults to logic 1
MUTE	14	7	active LOW mute input; when set LOW, sets the digital data to zero and either silences the output or switches it to analog FM, depending on the status of MUTEDEF (control bit in the I2C register) and RSSF; overridden by automute (if automute is used, then MUTE is automatically pulled LOW)
nC	15 10 17		not connected
VDDAR	18	8	analog supply voltage for the right audio channel
VSSAR	19	9	analog ground connection for the right audio channel
VRO	20	10	internal reference voltage buffer output
VRC	21	11	internal reference voltage buffer HIGH impedance node
nC	22		not connected
OPR	23	12	analog output from the right audio channel
EXTR	24	13	external analog input to the right audio channel
FMR	25	14	FM sound input to the right audio channel
INTR	26	15	integrator output from the right audio channel
CDR	27	16	integrator connection to an external damping capacitor
nC	28		not connected
VREF	29	17	reference voltage input; 2.5 V (typical)
VDAC	30	18	quiet Vss to DACs
CDL	31	19	integrator connection to an external damping capacitor
INTL	32	20	integrator output from the left audio channel
FML	33	21	FM sound input to the left audio channel
EXTL	34	22	external analog input to the left audio channel
OPL	35	23	analog output from the left audio channel
nC	36		not connected
VSSAL	37	24	analog ground connection for the left audio channel
VDDAL	38	25	analog supply voltage for the left audio channel

Suppliers Datasheet
		Exact Matc