PAL32YX10ACJS，there are the best PAL32YX10ACJS suppiers all over the world here.These are the list and detailed contact method of PAL32YX10ACJS suppliers all over the world as follows.You can buy or get informations of PAL32YX10ACJS through email , message or tel.

suppliers of PAL32YX10ACJS and PDF data of PAL32YX10ACJS

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
PAL32YX10ACJS	MMI	.	94		3528	Liverpool (Hong Kong) Electron.. Contact:Jessica Tel:86-755-83957717 Fax: Email: info@lvphk.com
PAL32YX10ACJS			94+		15	Anichip International Ltd. Contact:Andrew Tel:86-755-25873776 Fax:86-755-25873736 Email: andrew@anichip.com
PAL32YX10ACJS	15		MMI		94	Majestic Trading Contact:dena Tel:86-755-83002395 Fax: Email: carmen@mtc-ic.com
PAL32YX10ACJS		DIP	07+	STOCK	500	ICINTERNATIONALTRADINGCo. Contact:Ms.jennifer Tel:86-754-84470653 Fax:86-754-86674846 Email: weisenda@21cn.com
PAL32YX10ACJS	DIP	38503	MMI	MAILTOTALK	94	EuropeanUnionICIndustryCo. Contact:Ms.mikylin Tel:0086-0754-84479727 Fax:0086-0754-84470500 Email: dali11@qq.com

PAL32YX10ACJS Datasheet

Pin	Function	Description
TDI	Test Data In for JTAG	Hold HIGH during normal operation. Connect to VCC if not used for JTAG.
TRSTB	Active low Reset for JTAG	Hold LOW during normal operation. Connect to ground if not used for JTAG.
TMS	Test Mode Select for JTAG	Hold HIGH during normal operation. Connect to VCC if not used for JTAG.
TCK	Test Clock for JTAG	Hold HIGH or LOW during normal operation. Connect to VCC or ground if not used for JTAG.
TDO	Test data out for JTAG	Output that must be left unconnected if not used for JTAG.
STM	Special Test Mode	Must be grounded during normal operation.
l/ACLK	High-drive input and/or array network driver	Can be configured as either or both.
l/GCLK	High-drive input and/or global network driver	Can be configured as either or both.
I	High-drive input	Use for input signals with high fanout.
I/O	Input/Output pin	Can be configured as an input and/or output.
VCC	Power supply pin	Connect t0 3.3V supply.
GND	Ground pin	Connect to ground.

PAL32YX10ACJS Price

Input and Output The power supply to the control circuitry and the drains of the power-switch MOSFETs are connected to the two input pins, INl and IN2. These two pins are connected externally in most standard applications. The two ground nodes GND1 and GND2 must be connected externally in all applications. Pins OUTl, OUT2, and OUT3 are connections to the source nodes of the power-switch MOSFETs. In a typical application circuit, current flows through the switches from INl and IN2 to OUTx toward the load.
PAL32YX10ACJS on stock

Bezeichnung Description	Symbol Symbol	Wert Value		Einheit Unit
Bezeichnung Description	Symbol Symbol	SFH 203	SFH 203 FA	Einheit Unit
Fotoempfindlichkeit Spectral sensitivity VR = 5 V, Normlicht/standard light A, T= 2856 K, VR = 5 V, = 950 nm, Ee = 1 mW/cm2	S S	80(50)	50(30)	nA/lx
Wellenlange der max. Fotoempfindlichkeit Wavelength of max. sensitivity	S max	850	900	nm
Spektraler Bereich der Fotoempfindlichkeit S= 10 % von Smax Spectral range of sensitivity S= 10 % of Smax		4001100	8001100	nm
Bestrahlungsempfindliche Flache Radiant sensitive area		1	1	mmZ
Abmessung der bestrahlungsempfindlichen Flache Dimensions of radiant sensitive area	×B ×	1×1	1×1	mm×mm
Abstand Chipoberflache zu Gehauseober- flache Distance chip front to case surface	H	4.04.6	4.04.6	mm

* All specs and applications shown above subject to change without prior notice. 7 AN KAN RD LU~HU TAOYUAN TA~WAN RO~E ra~server@ceramate.com.tw Tel:886- 3-352 9445 H ttp: www.cera m ate.com.tw Fax:886 -3-3521052 Page 4 0f10 Rev l.1 Dec 26,2001

Suppliers Datasheet
		Exact Matc