PALR-02VF Datasheet where both VIN and VOUTare referred to the ground pin (Pin 3) of the LT1054. For LT1054 regulator circuits, the power dissipation will be equivalent to that of a linear regulator. Due to the limited power handling capability of the LT1054 packages,the userwill have to limit output current require- ments ortake stepsto dissipate some power externalto the LT1054 for large input/output differentials. This can be accomplished by placing a resistor in series with CIN as shown in Figure 6. A portion of the input voltage will then be d ropped acrossthis resistorwithout affecting the output regulation. Because switch current is approximately 2.2 times the output current and the resistor will cause a voltage drop when CIN iS both charging and discharging, the resistor should be chosen as: PALR-02VF Price| | | | S7810PI | | | Characteristic | Symbol | Test Condition | Min | Typ | Max | Unit | | | | | Tj =25 | 9.6 | 10.0 | 10.4 | V | | Output Voltage | VOUT | IOUT=5mA 1A VIN=12.5V 25V, Po 15W | 9.5 | 10.0 | 10.5 | | | | VIN=12.5V 28V | | | 7 | 200 | | | Line Regulation | VOUT | VIN=14.OV 20V | Tj =25 | | 2 | 100 | mV | | | | IOUT=5mA 1.5A | | | 12 | 200 | | | Load Regulation | VOUT | IOUT=250mA 750mA | T=25 | | 4 | 100 | mV | | Quiescent Current | IB | | T.i =25 | | 4.3 | 8.0 | mA | | | | VIN = 12.5V 28V | | | 1.0 | | | Quiescent Current Change | IB | IOUT = 5mA ^ 1A | | | 0.5 | mA | | Output Noise Voltage | VN | f=lOHz ^ 100KHz, | Tj =25 | | 70 | | uVrms | | Ripple Rejection Ratio | RR | f=120Hz, VIN =13V 23V | 55 | 71 | | dB | | Dropout Voltage | VD | IOUT=1A | Tj =25 | | 2.0 | | V | | Short Circuit Current Limit | Isc | | Tj =25 | | 0.4 | | A | | Output Voltage Drift | TCvo | IOUT=5mA | T=25 | | -1.0 | | mV/oC | | Peak Output Current | IPK | | Tj =25 | | 2.2 | | A | | | | | | | | |
PALR-02VF on stock| lB= | -430 | A | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | -280 | | | | | | | | | | -230 | | | | | | | | | | -180 | | | | | | | | | | -130 | | | | | | | | | | -80 | | | | | | | | | | | | | | | | | | | | |
| CONDITION | MIN | MAX | | Analogue supply voltage: AVDD | GND - 0.3V | GND +7V | | Digital supply voltages: DVDDl - 2 | GND - 0.3V | GND+7V | | Digital ground: DGND | GND - 0.3V | GND+ 0.3V | | Analogue grounds: AGNDl - 2 | GND - 0.3V | GND+ 0.3V | | Digital inputs, digital outputs and digital l/0 pins | GND - 0.3V | DVDD2+ 0.3V | | Analogue inputs (RINP, GINP, BINP) | GND - 0.3V | AVDD+ 0.3V | | Other pins | GND - 0.3V | AVDD+ 0.3V | | Operating temperature range: TA | 0] | +70YC | | Storage prior to soldering | 30YC max / 85% RH max | | Storage temperature after soldering | -65YC | +1 50YC | | Package body temperature (soldering, 10 seconds) | | +260YC | | Package body temperature (soldering, 2 minutes) | | +183IC | | | |
|
