RPC1507 Datasheet If active-high OUT polarity is selected, the pulses will only appear if there is a pull-up resistor in place and the fluid is not present (no detection, low output), or, if there is a pull-down resistor and the output is active (high output). If the sensor is wired to a microprocessor as shown in Figure 3-3, the microprocessor can reconfigure the load resistor to either ground or Vcc depending on the output state of the QT114, so that the pulses are evident in either state with either POL setting. RPC1507 Price| | | | | | | | | | | | | L | | | | | | r | 1= 5V | r | | | | | | cl' =1:F CniiT = 10d (Tantaluml | | | | | VOUT = 3.3V III | | | | | | | | |
RPC1507 on stock| | B3431 0.5% | | Parameter | Symbol | Condition | Min | Typ | Max | Units | | Reference Voltage | VREF | Vz = VREFl IZ = lOrriA(l) | 2.490 | 2.50 | 2.515 | V | | VREF Temp Deviation | VDEV | Vz = VREFl IZ = lOrriA(l) | | 4 | 17 | mV | | Ratio of Change in | VR EF | IZ = lOmA,AVz = 10V to VRef | -2.7 | -1.0 | | | | VREF To Change in Vz | AVz | Iz = lOmA,AVz = 36V t0 10V | -2.0 | -0.4 | 0.3 | mVV | | Reference Input Current | IREF | Rl = 10kl , R2 = o , IZ = lOrrlA(2) | | 0.7 | 4 | A | | IREF Temperature Deviation | IREF(DEV) | Rl = 10kl , R2 = o , Iz = lOrrlA(2) | | 0.4 | 1.2 | A | | Off-State Cathode Current | IZ (OFF) | VREF = OV, VZ =36V(3) | | 0.1 | 1 | A | | Dynamic Output Impedance | rz | F<lkHz, Vz = VREF Iz = ImA to lOOmA(') | | 0.20 | 0.50 | l | | Minimum Operating Current | IZ(MIN) | Vz= VREF(1) | | 0.4 | 1 | mA | | | | | | | |
| Symbol | Parameter | Test Condition | Min | Typ. | Max | Unit | | fc | Center Frequency | fCl | 54 | 60 | 66 | Hz | | fC2 | 63 | 70 | 77 | Hz | | fC3 | 72 | 80 | 88 | Hz | | fC4 | 90 | 100 | 1 10 | Hz | | QBASS | Quality Factor | Qi | 0.9 | 1 | 1.1 | | | Q2 | 1.1 | 1.25 | 1.4 | | | Q3 | 1.3 | 1.5 | 1.7 | | | Q4 | 1.8 | 2 | 2.2 | | | DCGAIN | Bass-DC-Gain | DC= off | -1 | O | 1 | dB | | DC= on | 3.5 | 4.4 | 5.5 | dB | | MID CONTROL | | L RANGE | Control Range | | ±13 | ±1 5 | ±17 | dB | | ASTEP | Step Resolution | | 0.5 | 1 | 1.5 | dB | | fc | Center Frequency | fCl | 450 | 500 | 550 | Hz | | fC2 | 0.9 | 1 | 1.1 | kHz | | fC3 | 1.35 | 1.5 | 1.65 | kHz | | fC4 | 1.8 | 2 | 2.2 | kHz | | QBASS | Quality Factor | Qi | 0.9 | 1 | 1.1 | | | Q2 | 1.8 | 2 | 2.2 | | | TREBLE CONTROL | | GMAX | Control Range | | ±13 | ±1 5 | ±17 | dB | | ASTEP | Step Resolution | | 0.5 | 1 | 1.5 | dB | | fc | Center Frequency | fCl | 8 | 10 | 12 | KHz | | fC2 | 10 | 12.5 | 1 5 | KHz | | fC3 | 12 | 15 | 18 | KHz | | fC4 | 14 | 17.5 | 21 | KHz | | SPEAKER ATTENUATORS | | Rin | Impedance @ACin0,2,3 | | 35 | 50 | 65 | kl | | Rin | Impedance @ACinl | Rinl | 35 | 50 | 65 | kl | | Rin2 | 28 | 40 | 52 | kl | | Rin3 | 21 | 30 | 39 | kl | | bMAX | Max. Gain | | 13 | 15 | 1 7 | dB | | AMAX | Max. Attenuation | | -74 | -79 | | dB | | ASTEP | Step Resolution | | 0.5 | 1 | 1.5 | dB | | AMUTE | Output Mute Attenuation | | 80 | 90 | | dB | | EE | Attenuation Set Error | | | | +2 | dB | | VDC | DC Steps | Adjacent Attenuation Steps | -5 | 0.1 | 5 | mV | | AUDIO OUTPUTS | | VCLIP | Clipping Level | d=0.3% | 1.6 | 1.8 | | VRMS | | RL | Output Load Resistance | | 2 | | | kl | | CL | Output Load Capacitance | | | | 10 | nF | | | | | | | |
|
