| Symbol | Parameter | Test conditions | Min | Typ. | Max | Unit |
| lBlASP | Pin 23-28-29 Bias Current (Current sourced by PNP base) | For V23-28-29 = 2V | | 2 | | |
| lBlASN | Pin 31 Bias Current (Current sunk by NPN base) | For V31=6V | | 0.5 | | cA |
| VSth | Vertical Sync Input Threshold Voltage | Pin 34, High-Ievel Low-level | 2 | | 0.8 | V V |
| VSBI | Vertical Sync Input Bias Current (Current Sourced by PNP Base) | V34= 0.8V | | 1 | | |
| VRB | Voltage at Ramp Bottom Point | On Pin 27 | | 2/8 | | VREF-V |
| VRT | Voltage at Ramp Top Point (with Sync) | On Pin 27 | | 5/8 | | VREF-V |
| VRTF | Voltage at Ramp Top Point (without Sync) | On Pin 27 | | VRT-O.1 | | V |
| IR27 | Output Current Range on Pin 27 during Ramp Charging Time. Current to Charge Capacitor between Pin 27 and Ground | V28 = 2V (Note 2), 2V < V27 < 5V Min current Max current | 100 | 15 135 | 20 | cA |
| vsw | Minimum Vertical Sync Pulse Width | Pin 34 | 5 | | | ccS |
| VSmDut | Vertical Sync Input Maximum Duty-cycle | Pin 34 | | | 15 | % |
| VSTD | Vertical Sawtooth Discharge Time Duration | On Pin 27, with 150nF cap | | 85 | | ccS |
| VFRF | Vertical Free Running Frequency (V28 = 2V) | Measured on Pin 27, Cosc (Pin27) = 150nF | | 100 | | Hz |
| ASFR | AUTO-SYNC Frequency (see Note 3) | With C2r = 150nF +5% | 50 | | 120 | Hz |
| RATD | Ramp Amplitude Thermal Drift | On Pin 30 (see Note l), (OoC < Tamb < 700C) | | 100 | | ppm/oC |
| RAFD | Ramp Amplitude Drift Versus Frequency | V31 = 6V, C27 = 150nF, 50Hz < F < 120Hz | | 200 | | ppm/Hz |
| Rlin | Ramp Linearity on Pin 27 C127/127 | V28 = 2V, V25 = X = 4.3V, 2.5V < V27 < 4.5V | | O5 | | % |
| Rload | Minimum Load on Pin 25 for less than l% Vertical Amplitude Drift | | 50 | | | M |
| Vpos | Vertical Position Adjustment Voltage on Pin 32 | V33 = 2V V33 = 4V V33 = 6V | 3.65 | 3.2 3.5 3.8 | 3.3 | V V V |
| IVPOS | Max Current on Vertical Position Control Output (Pin 32) | | | +2 | | mA |
| Vor | Vertical Output Voltage (on Pin 30) (Peak to Peak Voltage on Pin 30) | V31 = 2V V31 = 4V V31 = 6V | 3175 | 2 3 4 | 2.2 | V V V |
| VOUTDC | DC Voltage on Vertical Output (Pin30) | See Note 4 | | 7/16 | | VREF-V |
| VOI | Vertical Output Maximum Output Current | On Pin 30 | | +5 | | mA |
| dVS | Max Vertical S-Correction Amplitude (V28 = 2V Inhibits S-CORR; V28 = 6V gives Maximum S-CORR) (see Figure 3) | (l;XIN30pp at T/4 Cx/N30pp at 3T/4 | | -4 +4 | | % |
| Ccorr | C-Correction Adjustment Range Voltage on Pin 27 for Maximum Slope on the Ramp (with S-Correction) (see Figure 4) | V29 = 2V V29 = 4V V29 = 6V | | 3 3.5 4 | | V V V |
| | | | | | |
