SI9182DH5 SI9182DH5 SI9182DH5，there are the best SI9182DH5 SI9182DH5 SI9182DH5 suppiers all over the world here.These are the list and detailed contact method of SI9182DH5 SI9182DH5 SI9182DH5 suppliers all over the world as follows.You can buy or get informations of SI9182DH5 SI9182DH5 SI9182DH5 through email , message or tel.

suppliers of SI9182DH5 SI9182DH5 SI9182DH5 and PDF data of SI9182DH5 SI9182DH5 SI9182DH5

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

SI9182DH5 SI9182DH5 SI9182DH5 Datasheet

The MSOP-10 package heats at a rate of about 2000CiW (ejA). (Note that this value is approximate because it depends upon the copper tracks and ground planes on the pcb.) If V_IN = 5V and I_OUT = 100mA then the power dissipation will be approximately 500mW. Multiplying this by the ejA of 200, the part's internal temperature will be about 1000C higher than the ambient temperature. If the ambient temperature is 700C then the internal temperature will be approximately 1700C which will typically trigger the overtemperature circuit and depower the part.
SI9182DH5 SI9182DH5 SI9182DH5 Price

3 PIN T0-252	Dimensions m mches
JEDEC T0-252 (AA) Variation	MIN	NOM	MAX
A1			005
c	018		024
Dl	205
El	170
H	370		4IO
L	055	060	070
Ll	108 REF
L2	020 BSC

SI9182DH5 SI9182DH5 SI9182DH5 on stock

		Test Condition	Value
Symbol	Parameter		TA= 25YC			-40 t0 85IC		·55 t0 125IC		Unit
Symbol	Parameter	Vcc (V)	Min	Typ.	Max	Min	Max	Min	Max	Unit
tPLH tPHL	Propagation Delay	3.3C)	1.5	6.5	11.0	1.5	12.0	1.5	12.0
tPLH tPHL	Time SELECT to Y	5O	1.5	5.0	8.5	1.5	9.5	1.5	9.5	ns
tPLH tPHL	Propagation Delay	3.3C)	1.5	6.5	11.0	1.5	12.0	1.5	12.0
tPLH tPHL	Time STROBE to Y	5O(¨)	1.5	5.5	9.0	1.5	10.0	1.5	10.0	ns
tPLH tPHL	Propagation Delay	3.3C)	1.5	5.0	8.0	1.5	9.0	1.5	9.0
tPLH tPHL	Time A, B to Y	5O(¨)	1.5	4.0	6.5	1.5	7.0	1.5	7.0	ns

VOHV and VOLP are measured with respect to ground reference. Input pulses have the following characteristics: f = 1 MHz. t, = 3 ns. tf = 3 ns, skew < 150 ps. FIGURE l. Quiet Output Noise Voltage Waveforms 5. Set the HFS generator input levels at OV LOW and 3V HIGH for ACTQ devices and OV LOW and 5V HIGH for AC devices. Verify levels with an oscilloscope.

Suppliers Datasheet
		Exact Matc