ST93C86W6-6 Datasheet| | | | | | | I | | | | | | | | | | | | 1 | | 1 | | Il | lc | =( | ) | A | | | | | | 3 | I | 1 | | | | | | | | C= | OA | I | (j | {f | | 1 | | | | | | | | | -T -T | =250C =1250C III | | | = | | I | =75 = 501 | A | | | | | | | | | | | | | |
ST93C86W6-6 Price| | | F1 T 1- 12 L] 1 9 DimensionsMaBe in mm 1=B 2 3=C | Power dissipation - Verlustleistung 250 mW Plastic case SOT-23 Kunststoffgehause (T0-236) Weight approx. - Gewicht ca. 0.01 g Plastic material has UL classification 94V-O Gehausematerial UL94V-O klassifiziert Standard packaging taped and reeled Standard Lieferform gegurtet auf Rolle | | |
ST93C86W6-6 on stock| Parameter | Symbol | Conditions | Min | Typ | Max | Unit | | Collector-base voltage (Emitter open) | VCBO | Ic = 10 liA, IE = 0 | 50 | | | V | | Collector-emitter voltage (Base open) | VCEO | IC = 2 rriA, IB = 0 | 50 | | | V | | Collector-base cutoff current (Emitter open) | ICBO | VCB = 50 V,IE = 0 | | | 0 1 | LLA | | Collector-emitter cutoff current (Base open) | ICEO | VCE = 50 V,IB = O | | | 0 5 | yA | | Emitter-base cutoff current (Collector open) | IEBO | VEB = 6 V,Ic = 0 | | | 0.01 | mA | | Forward current transfer ratio | hFE | VCE = 10 V,IC = 5 mA | 160 | | 460 | | | hFE Rati0 8 | hFE(Small /Large) | VCE = 10 V,IC = 5 mA | 0.50 | 0.99 | | | | Collector-emitter saturation voltage | VCE(sat) | IC = 10 mA, IB = 0.3 mA | | | 0.25 | V | | Output voltage high-level | VOH | Vcc = 5 V, VB = 0.5 V, RL = 1 kQ | 4 9 | | | V | | Output voltage low-level | VOL | Vcc = 5 V, VB = 2.5 V, RL = 1 kQ | | | 0 2 | V | | Input resistance | Ri | | -30% | 10 | +30% | kQ | | Transition frequency | fr | VCB = 10 V, IE = -2 mA, f = 200 MHz | | 150 | | MHz | | | | | | | |
| TESTEN | ISOL TCK | ISOL TI | ISOL EXEC | Mode | Comments | | O | O | O | O | 82562G family Mode 0: . LEDs are 82562E-compatible ("A" configuration) . LAN_DISABLE# pin is used as ADV10 (auto-negotiation advertise 10M only) Alternative Mode: drop-in replacement for existing 82562E- based designs | The ISOL _TCK, ISOL_TCI, and ISOL_EXEC, and ADV10/ LAN_DISABLE# pins have internal 10 K Q pull-down resistors and should not be connected for Mode 0 (refer to Table 2). For the alternative 82562E drop-in replacement mode, pins may optionally be used as a LAN disable. | | O | O | 1 | 1 | 82562G family Mode l: . LEDs are in configuration B . LAN_DISABLE# pin is single pin LAN disable (tri-state and full power down function) | The ISOL _TCK pin has an internal 10 K Q pull-down resistor and should not be connected for Mode 1 (refer to Table 2). | | O | 1 | 1 | 1 | Isolate | Tri-state and power down. | | 1 | 0 | 1 | O | Testing Mode | | | 1 | O | O | O | XOR Tree | Board testing plus tri-state. | | 1 | 0 | 0 | 1 | 82562G family Mode 2: Same as 0011 except that LEDs are in configuration C | The ISOL_TCK and ISOL_TI pins have 10 K Q internal pull-down resistors and should not be connected for Mode 2 (refer to Table 2). | | 1 | O | 1 | 1 | 82562G family Mode 3: Same as 0011 except enhance Tx rise and fall times. | The ISOL_TCK pin has an internal 10 K Q pull-down resistor and should not be connected for Mode .) . | | 1 | 1 | O | O | 82562G family Mode 4: Same as 1001 except Enhance Tx rise and fall times. | The ISOL TI and ISOL EXEC pins have internal 10 KQ pull- down resistors and should not be connected for Mode 4. | | | | | | |
|
