STAEFA452 Datasheet This amplifier-sequenced hybrid (ASH) receiver is based on several leading-edge technologies that allow outstanding performance in a small and simple-to-apply module. Two surface-accoustic-wave (SAW) devices are employed. Front-end fil- tering by a low-loss coupled-resonator SAW filter provides excellent selectivity. Typical sensitivity better than -94 dBm is achieved with no RF oscillating or regener- STAEFA452 Price| PARAMETER | CONDITIONS | MIN | TYP | MAX | UNITS | | DC SPECIFICATIONS(1) VOH Output Voltage High, OUTp or OUTN VOL Output Voltage Low, OUTp or OUTN lvOD I Output DifferentiaIVoltage, IOUTp - OUTN I VOS Output Offset Voltage(2) CO OutputCapacitance(3) IAVOD I Change in lvOD IBetween o and 1 AVOS Change Between o and 1 ISOUT Output Short-Circuit Current ISOUTNP Output Current | RLOAD = 10002 +1%; See LVDS Timing Diagram, Page 7 RLOAD = 100fl+1% RLOAD = 100Q+1% RLOAD = 10002+1%; See LVDS Timing Diagram, Page 7 VCM = 1.5V RLOAD = 1000! +1% RLOAD = 100Q+1% Drivers Shorted to Ground Drivers Shorted Together | 900 300 1100 | 1375 1025 350 1200 4 | 1500 400 1300 25 25 40 12 | mV mV mV mV pF mV mV mA mA | | DRIVER AC SPECIFICATIONS Clock Clock Signal Duty Cycle Minimum Data Setup Tlme(4, 5) Minimum Data Hold Time(4, 5) tRISE~ALL VOD Rise Time or VOD Fall Time | 6 x ADCLK 10 = 2.5mA 10 = 3.5mA 10 = 4.5mA 10 = 6mA | 45 | 50 650 650 400 250 200 150 | 55 | % ps ps ps ps ps | | | | | | |
STAEFA452 on stock| Inspection 11 | MIL-STD-750 | Symbol | Limits | Unit | | Method | Conditions | Min | Max | | Subgroup 5 - Continued Safe operating area (switching) Test 1 2N6032 2N6033 Test 2 Electrical measurements Safe operating area (switching) 2N6032 2N6033 2N6032 2N6033 Electrical measurements Subarouos 6 and 7 Not applicable | 3053 | Load condition C; (unclamped inductive lead) (see figure 5); Tc = +250C; Duty cycle i 10 percent; RS = 0.1 ohm; tp ~ 10 ms; RBBl = 1Q; VBBl = 10 V dc max; RBB2 = 20Q; VBB2 = 4 V dc; IC = 50 A dc; IC = 40 A dc; Vcc = 10 V dc L = 50 UH, 0.1 Q; tp ~ 10 ms; RBBl = 10Q; VBBl = 10 V dc max; RBB2 = 20Q; VBB2 = 4 V dc; lc = 10 A dc; Vcc = 10 V dc L = 500 UH, 0.1 Q See table l, group A, subgroup 2 TA = +250C; duty cycle i 10 percent. tp ~ 10 ms (vary to obtain lc); RSil Q; Vcc > 50 V dc; L = 50 liH, 0.1 Q IC = 50 A dc; IC = 40 A dc; clamp voltage = 90 V dc; clamp voltage = 120 V dc; (see figure 6) See table l, group A, subgroup 2 | | | | | | | | | | | |
| CHARACTERISTIC | SYMBOL | RATING | UNIT | | Forward Current | IF | 50 | mA | | Reverse Voltage | VR | 4 | V | | Power Dissipation | PD | 125 | mW | | Operating Temperature | To | -3085 | oC | | Storage Temperature | Ts | -40120 | oC | | | | |
|
