STEL-3103-CR，there are the best STEL-3103-CR suppiers all over the world here.These are the list and detailed contact method of STEL-3103-CR suppliers all over the world as follows.You can buy or get informations of STEL-3103-CR through email , message or tel.

suppliers of STEL-3103-CR and PDF data of STEL-3103-CR

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

STEL-3103-CR Datasheet


		VGE=2f		W 15V	12V
		i l
		j\|\|
			}h	f
			}h	f
		t	\|f			10V
		1f?

		17
	l
	l

Ij						8v

STEL-3103-CR Price

unit (-)20 V (-)15 v (-)5 v (-)500 mA . (-)1 A 150 mW 150 0C -55 to +150 0C min typ max unit ( -)0.1 pA ( -)0.1 pA 135X 600X (70)80 300. MHz (400) (6.5)4.0 pF (-)15 (-35)30 mV 160 300 mV (-200) (-360) (-)0.95 (-)1.2 V (-)20 V (-)15 . v (-)5 v
STEL-3103-CR on stock

			Version
Parameter	Symbol	Test Condition	-2A	-33	-36	Unit	Note
Operating Current (One Bank Active)	lcci	Burst Lenth=2 tRC > tRc(rliin) IOL=OmA, tcc= tcc(min)	315	285	270	mA	1
Precharge Standby Current in Power-down mode	Icc2P	CKE i VIL(max), tcc= tcc(min)	15	15	15	mA
Precharge Standby Current in Non Power-down mode	Icc2N	CKE > VIH(min), CS > VIH(min), tcc= tcc(min)	75	65	65	mA
Active Standby Current power-down mode	ICC3P	CKE i VIL(max), tcc= tcc(min)	75	70	65	mA
Active Standby Current in Non Power-down mode	ICC3N	CKE > VIH(min), CS > VIH(min), tcc= tcc(min)	240	220	210	mA
Operating Current ( Burst Mode)	ICC4	IOL=OmA ,tcc= tcc(min), Page Burst, All Banks activated.	505	465	445	mA
Refresh Current	lccs	tRC > tRFc(rTiin)	280	250	230	mA	2
Self Refresh Current	ICC6	CKE0.2V	8	8	8	mA
Operating Current (4Bank interleaving)	ICC7	Burst Length=4 tRC > tRc(min) IOL=OmA, tcc= tcc(min)	600	550	520	mA

Byte Sequence	Byte Name	Bit Sequence	Byte Description
1	Slave Address	1 1010010	Commands the RC7106 to accept the bits in Data Bytes 3-6 for internal register configuration. Since other devices may exist on the same common serial data bus, it is necessary to have a specific slave address for each potential receiver. The slave receiver address for the RC7106 is 11010010. Register setting will not be made if the Slave Address is not correct (or is for an alternate slave receiver).
2	Command Code	Don't Care	Unused by the RC7106, therefore bit values are ignored (don't care). This byte must be included in the data write sequence to maintain proper byte allocation. The Command Code Byte is part of the standard serial communication protocol and may be used when writing to another addressed slave receiver on the serial data bus.
3	Byte Count	Don't Care	Unused by the RC7106, therefore bit values are ignored (don't care). This byte must be included in the data write sequence to maintain proper byte allocation. The Byte Count Byte is part of the standard serial communication protocol and may be used when writing to another addressed slave receiver on the serial data bus.
4	Data Byte 0	Refer to	The data bits in these bytes set internal RC7106 registers that control
5	Data Byte l	Table 5	device operation. The data bits are only accepted when the Address Byte bit sequence is 11010010, as noted above. For description of bit
6	Data Byte 2		control functions, refer to Table 4, Data Byte Serial Configuration Map.
7	Data Byte 3
8	Data Byte 4
9	Data Byte 5
1 0	Data Byte 6

Suppliers Datasheet
		Exact Matc