TNL27WZ07DTT1，there are the best TNL27WZ07DTT1 suppiers all over the world here.These are the list and detailed contact method of TNL27WZ07DTT1 suppliers all over the world as follows.You can buy or get informations of TNL27WZ07DTT1 through email , message or tel.

suppliers of TNL27WZ07DTT1 and PDF data of TNL27WZ07DTT1

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
TNL27WZ07DTT1	ON SEMICONDU				3000	ULTEST INTERNATIONAL TRADING C.. Contact:Veronica Lai Tel:86-755-23971083 Fax:86-755-82837284 Email: veronica@ultest.com

TNL27WZ07DTT1 Datasheet

- In case of under-Voltage, the failure is not latched. As soon as Vs falls below the under-Voltage detection threshold, the output stage switches in tristate and the status- flag is set from high level to low-level. If the voltage has risen above the specified value again, the output stage switches on again and the status-flag is reset to high-level. The Under Voltage failure is shown at the SF pin for Vs in the voltage range below the detection threshold (typical 4.2V) down t0 2.5V. - In the SF-mode, all internal circuitry is supplied by the voltage on Vs. For that reason, a loss of Vs supply voltage leads to a reset of all stored information (Power-ON- Reset). This Power-ON-Reset occurs as soon as under-Voltage is detected on Vs - In case of short circuit, over-current or over-temperature, the fault will be stored. The output stage remains in tristate and the status-flag at low-level until the error is reset by one of the following conditions: H -> L on DIS, L -> H on EN or Power-ON Reset.
TNL27WZ07DTT1 Price

SYMBOL	PARAMETER	CONDITIONS	TYP	MAX	UNIT
VF	forward voltage	IF= 50 mA	0.95	1.1	V
IR	reverse leakage current	VR= 60V		100	nA
Cd	diode capacitance	VR = 0; f= 1 MHz	0.4		pF
		VR = 1 V; f= 1 MHz	O35	0.45	pF
		VR = 20 V; f= 1 MHz	0.25	0.32	pF
rD	diode forward resistance	f = 100 MHz; note 1 IF = 0.5 mA IF = 1 mA IF = 10 mA IF = 100 mA	3.4 2.4 1.2 0.85	5.0 3.6 1.8 1.3	I I I
IS2112	isolation	VR = 0; f= 900 MHz	16.6		dB
		VR = 0; f = 1800 MHz	11.6		dB
		VR = 0; f= 2450 MHz	9.2		dB
IS2112	insertion loss	IF = 0.5 mA; f= 900 MHz	0.26		dB
		IF = 0.5 mA; f= 1800 MHz	0.35		dB
		IF = 0.5 mA; f = 2450 MHz	0.44		dB
IS2112	insertion loss	IF = 1 mA; f= 900 MHz	0.20		dB
		IF = 1 mA; f= 1800 MHz	0.29		dB
		IF = 1 mA; f= 2450 MHz	O38		dB
IS2112	insertion loss	IF = 10 mA; f= 900 MHz	0.13		dB
		IF = 10 mA; f= 1800 MHz	0.22		dB
		IF = 10 mA; f = 2450 MHz	0.32		dB
IS2112	insertion loss	IF = 100 mA; f= 900 MHz	0.10		dB
		IF = 100 mA; f= 1800 MHz	0.20		dB
		IF = 100 mA; f= 2450 MHz	0.29		dB
TL	charge carrier life time	when switched from IF = 10 mA to IR = 6 mA; RL = ioo I ; measured at IR = 3 mA	0.5		oS
Ls	series inductance	IF = 100 mA; f= 100 MHz	1.5		nH

TNL27WZ07DTT1 on stock

	ltem	Setting value
1	Panel	1.60" (32.4mm x 24.3mm)
2	Panel shift	None
3	Dot pitch	13.5pm x 40.5pm
4	Maximum image height	20.25mm
5	Overscan	-2.0%
6	Effective panel size	1.60" (32.4mm x 24.3mm)
7	Effective projection size	40" t0 50" (screen size)
8	Projection magnification	24.631 times/40" (including distortion)

1 Prior to the onset of overvoltage clamping. For voltages above this value, safe operation is limited by the overvoltage clamping energy 2 A higher Ti is allowed as an overload condition but at the threshold TjcTO) the over temperature trip operates to protect the switch. 3 All control logic and protection functions are disabled during conduction of the source drain diode.

Suppliers Datasheet
		Exact Matc