TSM-136-03-S-SV-P，there are the best TSM-136-03-S-SV-P suppiers all over the world here.These are the list and detailed contact method of TSM-136-03-S-SV-P suppliers all over the world as follows.You can buy or get informations of TSM-136-03-S-SV-P through email , message or tel.

suppliers of TSM-136-03-S-SV-P and PDF data of TSM-136-03-S-SV-P

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

TSM-136-03-S-SV-P Datasheet

General Description The Micron~ Imaging MT9TO01 is a QXGA-format l/2- inch CMOS active-pixel digital image sensor with an active imaging pixel array of 2,048H x l,536V It incor- porates sophisticated camera functions on-chip such as windowing, column and row skip mode, and snap- shot mode. It is programmable through a simple two- wire serialinterface.
TSM-136-03-S-SV-P Price

		Min	Typ	Max
Collector saturation voltage - Kollektor-Sattigungsspannung Ic = 10 mA,IB = 0.5 mA . VCEsat Ic = 100 mA, IB = 5 mA VCEsat			80 mV 200 mV	200 mV 600 mV
Base saturation voltage - Basis-Sattigungsspannung Ic = 10 mA, IB = 0.5 mA VBEsat Ic = 100 mA, IB = 5 mA VBEsat			700 mV 900 mV
Base-Emitter voltage - Basis-Emitter-Spannung VCE = 5 V, IC = 2 mA VBE VCE = 5 V, IC = 10 mA VBE		580 mV	660 mV	700 mV 720 mV
Collector-Emitter cutoff current - Kollektorreststrom VCE = 80 V BC 546 VCE = 50 V BC 547 VCE = 30 V BC 548 VCE = 30 V BC 549	ICES ICES ICES ICES		0.2 nA 0.2 nA 0.2 nA 0.2 nA	15 nA 15 nA 15 nA 15 nA
Collector-Emitter cutoff current - Kollektorreststrom VCE = 80 V, Tj = 1250C BC 546 VCE = 50 V, T.i = 125 aC BC 547 VCE = 30 V, Tj = 1250C BC 548 VCE = 30 V, Tj = 1250C BC 549	ICES ICES ICES ICES			4 }iA 4 l_r,A 4 }iA 4 IJ,A
Gain-Bandwidth Product - Transitfrequenz VCE = 5 V, IC = 10 mA, f= 100 MHz fr			300 MHz
Collector-Base Capacitance - Kollektor-Basis-Kapazitat VCB = 10 V, f= 1 MHz CCBO			3.5 pF	6 pF
Emitter-Base Capacitance - Emitter-Basis-Kapazitat VEB = 0.5 V, f= 1 MHz CEBO			9 pF
Noise figure - RauschmaB VCE = 5 V, IC = 200 }iA BC 547 Rc = 2 kQ f= 1 kHz, BC 548 A f= 200 Hz BC 549	F F F		2 dB 1.2 dB 1.2 dB	10 dB 4 dB 4 dB

TSM-136-03-S-SV-P on stock

Tu= -50'C

2 5'C

(

1 50'C

PROGRAM/ERASE STATUS: The device provides several bits to determine the status of a program or erase operation: 1/02, 1/05, l/06 and l/07. The "Status Bit Table" on page 10 and the following four sections describe the function of these bits. To provide greater flexibility for system designers, the AT49BV802A(T) contains a programmable configuration register. The configuration register allows the user to specify the status bit operation. The configuration reg- ister can be set to one of two different values, "00" or "01". If the configuration register is set to "00", the part will automatically return to the read mode after a successful program or erase operation. If the configuration register is set to a "01", a Product ID Exit command must be given after a successful program or erase operation before the part will return to the read mode. It is important to note that whether the configuration register is set to a "00" or to a '01", any unsuccessful program or erase operation requires using the Product ID Exit command to return the device to read mode. The default value (after power-up) for the configuration regis- ter is "00". Using the four-bus cycle Set Configuration Register command as shown in the "Command Definition in Hex" table on page 11, the value of the configuration register can be

Suppliers Datasheet
		Exact Matc